BetaFPV HX100 SE PNP

Focusing on the concept of racing and freestyle, here comes HX100 SE - As the first 1S toothpick drone in the current market, HX100 SE is the drone you definitely should have a try! It is tiny enough to fly everywhere, light enough to take a smooth flight like a free bird and powerful enough to rip out the world!
With the lightest F4 1S Brushless FC V2.1, newest BT2.0 banana connector, powerful 1102 13500KV motor and cutomized HX100 SE carbon fiber frame, you will experience the unparalleled outdoor flying with BT2.0 300mAh 1S battery.

BULLET POINT

• HX100 SE - The first 1S toothpick drone in the current market. With the tiny design of 100mm wheelbase, small body contains so much energy! This little beast will bring you unprecedented outdoor flight experience with BT2.0 300mAh 1S battery.
• Uses our newest and lighest F4 1S Brushless FC V2.1, which only weights 2.69g without cable. This FC possesses efficient STM32F411CEU6 processor and tuned Betaflight MATEKF411RX (MK41R), which achieved maximum weight savings.
  
• Equips with BetaFPV exclusive designed BT2.0 banana connector, which can support 9A continuous current and 10A burst while the PH2.0 connector just supports 4.5A continuous current. Solving the low voltage warning issue of PH2.0 connector on 1S brushless whoop when you start flying. It enables you to enjoy a longer flight time and powerful flight experience.
• The high efficient combination of light 1102 13500KV motor and durable 65mm 2- blade props brings the drone with excellent flight performance. Customized 1102 13500KV motor has exquisite workmanship and it is with strengthened cable connectors. It is more thicker which will not easy to break off. Whole drone no soldering or tinkering necessary.
• Super light with a total weight of 28.09g, it gives pilots a good balance of weight and nice punch on 1S battery, which leads to awesome and powerful flight performance.
• Installs with cutomized HX100 SE carbon fiber frame. It is specially made of T300 material and also matted, which makes this frame more textured and durable.
• Thoughtful design on package - The drone comes with BT2.0-PH2.0 adapter cable in default, which is convenient for customer who uses PH2.0. We also released the BT2.0 charger, its charging current has been upgraded from 0.5A to 1A, which makes the charge speed increase to 2 times.

SPECIFICATION

• Weight: 28.09g (without battery)
• FC&ESC: F4 1S Brushless FC V2.1
• Motors: 1102 13500KV Motors
• Props: 65mm 2-blade props(1.5mm shaft hole)
• Camera: M01 AIO Camera
• VTX: M01 25MW 5.8G VTX
• Frame:HX100 SE Carbon Fiber Frame
• Canopy: Canpy for HX100 SE
• Receiver Option: Frsky XM / DSMX / Futaba S-FHSS
• Battery: BT2.0 300mAh 1S Battery
• Flight time: 4 mins in a smooth outdoor flight, 2:30 mins in full throttle outdoor flight

F4 1S BRUSHLESS FC V2.1

Find more details about this F4 1S Brushless FC V2.1 in another page.

FC

• CPU: STM32F411CEU6 ( 100MHZ )
• Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
• Size: 29mm x 29mm, fully compatible with the whoop frame in the current market.
• Firmware version: Betaflight MATEKF411RX (MK41R)
• OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
• Power Cable: 60mm, with JST-PH 2.0 connector, 1.25mm motor header pins

ESC

• Power supply: 1S
• Current: 5A continuous and peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: O_L_5_REV16_6.HEX
• Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

BT2.0 WHOOP CABLE PIGITAIL

BT 2.0 1S whoop cable pigtail has the features of durability and high efficiency. One important factor which caused those features is that it is with banana connectors. Supports 9A continuous current (PH 2.0 is about 4.5A), which can make the best potential of HX100 SE.

The problem of voltage drop which existed on the PH2.0 has been solved. There is no need to worry about the low voltage warning issue when you start flying.

Besides that, it comes with light and customized 22AWG wire.

M01 AIO CAMERA AND M01 VTX

The M01 AIO camera is with a super Mini 5.8GHz FPV Transmitter + 600TVL FPV Camera + RG178 Antenna. It has both fast responce and clear image.

What's more, M01 vtx board is super light and perfectly suitable for HX100 SE canopy. SmartAudio is supported. Comes with 25° and 35° camera tilts mount in default, 35° mount is suitable for high-speed flight, while 25° mount is for lower speed flight.

• Output power: 25mW
• TVL: 600TVL
• FOV: H:120°/V:100°
• Video System: NTSC
• Horizontal Resolution: 640X480 1/4”
• Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz

Note: How to change the frequency or output power via remote control, please check the manual Smart Audio. Download the STL file for the customized HX100 SE canopy.

HX100 SE T300 CARBON FIBER FRAME

This frame is made of T300 material and also matted. The newly structure design of 2mm thickness and 4g weight, which makes this frame more textured and durable.

RECOMMEND BATTERY

Highly recommend BT2.0 300mAh 1S battery. This battery has adopted the newest technology of BT2.0 solid connector, its continous current is up to 9A. That is one of the most important factors which leads up to HX100 SE's awesome and powerful flight performance.

How to calculate the highest current the battery could provide? For example, 45C 300mAh 3S battery, the maximum discharge current is about 13.5A.

45C * 300mAh = 13.5A.

Package

• 1 * HX100 SE FPV Quad(without battery)
• 1 * BT2.0 300mAh 1S Battery
• 1 * BT2.0-PH2.0 Adapter Cable